Betekenis van:
lower class

Voorbeeldzinnen

1. The notion of upper-class and lower-class among humans in this world is a topic likely to be found in a woman's essay. Anyone who thinks that falls in the lower-class category of humans.
2. Class 4 Parts in contact with gas subject to the pressure lower than 20 kPa.
3. A train equipped with a Class A On-board system for a given level of application shall be able to operate on that level and any lower one.
4. In order to justify the classification of a malfunction into Class C the manufacturer shall demonstrate that emissions are lower than the regulated emission limits.
5. In order to justify the classification of a malfunction into Class B1 the documentation shall clearly demonstrate that, in some circumstances, the malfunction results in emissions that are lower than the OTLs.
6. The target system described in the attached TSI (Class A system) builds upon computer-based technology with a life expectancy significantly lower than current traditional railway signalling and telecommunication facilities.
7. Class C2 tyres: Tyres conforming to ECE Regulation No 54 and identified by a load capacity index in single formation lower or equal to 121 and a speed category symbol higher or equal to ‘N’;
8. for substances where a specific concentration limit is set for the relevant hazard class or differentiation either in Part 3 of Annex VI or in the classification and labelling inventory referred to in Article 42, and where the hazard class or differentiation is mentioned in Table 1.1, the lower of the specific concentration limit and the relevant generic cut-off value in Table 1.1; or
9. ‘Low floor bus’ is a vehicle of class I, II or A in which at least 35 % of the area available for standing passengers (or in its forward section in the case of articulated vehicles, or in its lower deck in the case of double-decker vehicles) forms an area without steps and includes access to at least one service door.
10. .7 Doors and door frames in “B” class divisions and means of securing them shall provide a method of closure which shall have resistance to fire equivalent to that of the divisions except that ventilation openings may be permitted in the lower portion of such doors.
11. .2b In new class B, C and D ships constructed on or after 1 January 2003, where a thin plated duct with a free cross-sectional area equal to or less than 0,02 m2 passes through ‘A’ class bulkheads or decks, the opening shall be lined with a steel sleeve having a thickness of at least 3 mm and a length of at least 200 mm, divided preferably into 100 mm on each side of the bulkhead or, in the case of the deck, wholly laid on the lower side of the decks pierced.
12. In the case of class ‘B’ front fog lamps the vertical inclination of the cut-off to be set in the unladen vehicle state with one person in the driver's seat shall be –1,5 per cent or lower [10] Vehicle types which do not comply with this provision may continue to be approved until 18 months after the entry into force of Supplement 4 to the 03 Series of Amendments.
13. In particular, they claimed that the majority of fasteners produced in the PRC: (i) are standard products (mainly ranging between 4.8 and 8.8 class of resistance) having no special characteristics regarding raw material, resistance, coating, or certification/safety related aspects; (ii) they are destined for lower-end applications (non-professional use and general distribution) as opposed to high-tech applications; and (iii) they do not meet the strict requirements of specific end-users such as the automotive, chemical or aerospace industry.
14. In new class B, C and D ships constructed on or after 1 January 2003, where fire dampers are placed behind ceilings or linings, these ceilings or linings shall be provided with an inspection door on which a plate reporting the identification number of the fire damper is provided. The fire damper identification number shall also be placed on any remote controls required. .2b In new class B, C and D ships constructed on or after 1 January 2003, where a thin plated duct with a free cross-sectional area equal to or less than 0,02 m2 passes through “A” class bulkheads or decks, the opening shall be lined with a steel sleeve having a thickness of at least 3 mm and a length of at least 200 mm, divided preferably into 100 mm on each side of the bulkhead or, in the case of the deck, wholly laid on the lower side of the decks pierced.
15. On vehicles of Class III the seats on one side or on both sides of the gangway may be movable laterally, it being then possible to reduce the width of the gangway to a figure corresponding to a lower cylinder diameter of 220 mm, on condition that the operation of a control on each seat, readily accessible to a person standing in the gangway, shall be sufficient to cause the seat to return easily and, if possible, automatically, even when it is loaded, to the position corresponding to a minimum width of 300 mm.